The OptiX OSN 500 is used at the access layer of the transmission network. It can provide STM-1/STM-4 optical interfaces and forms the entire equipment group with the other access layer equipment, thus optimizing the Huawei OptiX product series.

Network Application

Networking Application

Except for the basic principles for planning a network, you need to plan a network according to the NE type and networking mode supported by the OptiX OSN 500. The OptiX OSN 500 can form a network alone or with Huawei SDH equipment or third-party transmission equipment.

Independent Networking

The OptiX OSN 500 can form a chain or ring network alone.

Hybrid Networking with OptiX Transmission Equipment

The OptiX OSN 500 can form a network with other transmission equipment.

Service Type

The OptiX OSN 500 supports various types of services and provides abundant functions and features, to ensure the quality and efficiency of the service transmission.

The OptiX OSN 500 can access the following types of services:

SDH service signals
PDH service signals
Ethernet service signals

Capacity

The service capacity of the OptiX OSN 500 consists of the cross-connect capacity and the maximum access capacity.

Cross-Connect Capacity
The OptiX OSN 500 supports the higher-order full cross-connections of 21.25 Gbit/s or lower-order full cross-connections of 5 Gbit/s.
Access Capacities of Slots
This section provides slot access capacities of the OptiX OSN 500.
Maximum Access Capability
The OptiX OSN 500 can access services through various interfaces.

Networking Capability

The OptiX OSN 500 can form multiple network topologies such as the ring network and chain network.

The OptiX OSN 500 supports separate and combined configuration of the following types of NEs: terminal multiplexer (TM) and add/drop multiplexer (ADM). The OptiX OSN 500 can form a chain or ring network by using the STM-1/STM-4 optical interfaces.

When the OptiX OSN 500 functions as the access equipment, it can network with Huawei Metro and OSN equipment series. The OptiX OSN 500 can also network with third-party equipment.

Network Management System

The OptiX OSN 500 adopts the T2000 as the integrated NMS.

The T2000 can implement the integrated management of the entire optical transmission system and can also provide end-to-end management function if required. The T2000 improves the network quality and reduces maintenance costs, thus ensuring reasonable utilization of network resources.

An login to the LCT is not allowed during an login to the NMS. After a 30-minute logout of the NMS, an login to the LCT is allowed.

Software Architecture

The software system is of a modular design. Each module provides specific functions and works with other modules.

The entire software is distributed in three modules including board software, NE software and NM system.

The software resides respectively on functional boards, the SCC, and NM computer. Hierarchical structure ensures that it is highly reliable and efficient. Each layer performs specific functions and provides service for the upper layer.

Table 1 Weight, dimensions, and power consumption of the OptiX OSN 500

Equipment OptiX OSN 500

Power Consumption About 46 W (full configuration)

Weight About 4 kg (full configuration)

Dimensions 442 mm (width) x 220 mm (depth) x 44 mm (height) (1U)

Table 2 Service access capacity of the OptiX OSN 500

Service Type Maximum Number of Services Supported (channel)

STM-4 standard services 2

STM-1 standard services 6

E3/T3 services 6

E1/T1 services 105

Fast Ethernet (FE) services 24

Gigabit Ethernet (GE) services 2

Table 3 Power consumption and weight of the boards on the OptiX OSN 500

Board Power Consumption (W) Weight (kg)

ISU 21.3 1.12

SL1D 3.5 0.3

SP3D 11.9 0.85

PL3T 4.5 0.3

EGT1 8.3 0.6

EFS8 13 0.65

Table 4 Climate requirements for storage

Item Scope

Altitude ≤ 4,000 m

Air pressure 70 kPa to 106 kPa

Temperature -40°C to +70°C

Temperature change rate ≤ 1°C/min

Relative humidity 5%-100%

Solar radiation ≤ 1120 W/s2

Heat radiation ≤ 600 W/s2

Wind speed ≤ 30 m/s

S1018750 Typical Configuration

02310GEJ	TNHMMODELF02	8xFE/21xE1/75ohm/2xSTM-1(S-1.1) Main control Equipment integrated photoelectric optical transmission module(220VAC),4(FC-LC,10m)/175ohm(10m)/Symmetric Twisted-Pair(30m)
	TNHB00CASE01	Assembly Chassis(220V)
	TNHD00ISUC01	8xFE/21xE1/75ohm/2xSTM-1(S-1.1,LC)Integrated System Control Unit,ESFP Opitcal Module
	FSFL01001	Fibre-optical jumper wire-LC/UPC-FC/UPC-single mode-G.657A2-2mm-10m
	T-75-21-Anea 96F-10	Trunk Cable,10m,75ohm,21E1,1.6mm,Anea 96F-I,SYFVZP75-1.1/0.26*42(S),+45deg
	CAB-DL4217-30	DL4217-standard network cable30m-8PIN connector/8 corecategory 5 cable/8PIN connector-HONET


02310GEH	TNHMMODELE02	8xFE/21xE1/75ohm/2xSTM-4(S-4.1) Main control Equipment integrated photoelectric optical transmission module(-48VDC),4(FC-LC,10m)/175ohm(10m)/Symmetric Twisted-Pair(30m)
	TNHB1CASE	Assembly Chassis(-48V)
	TNHD00ISUC03	8xFE/21xE1/75ohm/2xSTM-4(S-4.1,LC)Integrated System Control Unit,ESFP Opitcal Module
	FSFL01001	Fibre-optical jumper wire-LC/UPC-FC/UPC-single mode-G.657A2-2mm-10m
	T-75-21-Anea 96F-10	Trunk Cable,10m,75ohm,21E1,1.6mm,Anea 96F-I,SYFVZP75-1.1/0.26*42(S),+45deg
	CAB-DL4217-30	DL4217-standard network cable30m-8PIN connector/8 core category 5 cable/8PIN connector-HONET


machine box size	442mm(W)×220mm(D)×44mm(H)
machine box weight	2kg(NW of machine boxjust include POWER and FAN)