top rated bts base station use for stairwells

Product Introduction

The RRU3939 is an outdoor remote radio unit. It is the RF part of a distributed base station,  powered by a power cabinet, and can be located near the antenna. The RRU3939 performs  modulation, demodulation, data processing, and combination and division of baseband signals  and RF signals. With the Software Defined Radio (SDR) technology, the RRU3939 can  support the GL dual-mode operation through corresponding software configuration. 

The RRU3939 has a dual-transmitter and dual-receiver (2T2R) design, which further  improves the output power and the carrier capacity. 

Physical Ports

Each RRU has a modular structure. Its external ports are located at the bottom of the module  and in the cabling cavity.

Frequency Band

Frequency  Band (MHz):1800

RX Frequency Band (MHz):1710–1785

TX Frequency Band (MHz):1805–1880

Capacity

Single-mode capacity 

GSM:Each RRU3939 supports 8 carriers.

LTE:Each RRU3939 supports 2 carriers. The LTE bandwidth is 1.4, 3, 5, 10,  15, or 20 MHz.

Multi-mode capacity

Typical Output Power

• RRU3939 modules operating in GSM mode and in the 1800 MHz frequency band comply with ETSI EN 301 502 V9.2.1. RRU3939 modules operating in LTE or Multi-Standard Radio (MSR) mode and in the 1800 MHz frequency band comply with ETSI EN 301 908 V5.2.1 and 3GPP TS 37.104.

• For the RRU3939 working in GSM mode: when the S1 or S2 configuration is applied, each carrier on the RRU3939 supports a maximum of 60 W output power, and the corresponding license must be obtained. After design optimization, the 8PSK and GMSK modulation schemes support the same output power for each carrier on the RRU3939 when any of the S1 through S6 configurations is used.

When the S7 or S8 configuration is used, the license controlling the GBFD-118104 Enhanced EDGE Coverage feature must be obtained so that the 8PSK and GMSK modulation schemes support the same output power for each carrier on the RRU3939.

• The output power is 1 dB less than the standard power when the RRU3939 is located at a height of 3500 m to 4500 m (11482.9 ft to 14763.8 ft); and is 2 dB less than the standard power when the RRU3939 is located at a height of 4500 m to 6000 m (14763.8ft to 19685.0 ft).

• Factors such as the site-to-site distance, frequency reuse factor, power control algorithm, and traffic model affect the gain achieved by dynamic power allocation. Therefore, in most cases, the network planning can be based on the actual power specifications achieved by dynamic power allocation.

• In power sharing mode, the power control and DTX functions must be enabled. In GBSS8.1, the dynamic power sharing feature is mutually exclusive with the GBFD-113201 Concentric Cell, GBFD-114501 Co-BCCH Cell, GBFD-118001 BCCH Dense Frequency Multiplexing, and GBFD-117501 Enhanced Measurement Report (EMR) features. In GBSS9.0 and later versions, the dynamic power sharing feature can be used together with these features. However, in GBSS8.1, GBSS9.0, and later versions, the dynamic power sharing feature currently cannot be used together with the GBFD-117002 IBCA (Interference Based Channel Allocation), GBFD-117001 Flex MAIO, GBFD-118701 RAN Sharing, and GBFD-114001 Extended Cell features.

• Power sharing assumes a random distribution of UEs in the cell.

Power Consumption

• The typical power consumption and the maximum power consumption are reached when the base

station works at a temperature of 25°C. l

• The typical power consumption for GSM is reached when the base station works with 30% load and

power control and DTX are enabled. The maximum power consumption for GSM is reached when

the base station works with 100% load.

• The typical power consumption for LTE is reached when the base station works with 50% load. The

maximum power consumption for LTE is reached when the base station works with 100% load.

Equipment Specifications

Dimensions (H x W x  D):400 mm x 300 mm x 150 mm (without the housing)

Weight:20 kg (without the housing)