Related Products
14 years optical transmitter,optical line terminal equipment,communication equipment experience
14 years optical transmitter,optical line terminal equipment,communication equipment experience
The OptiX OSN 500 is used at the access layer of the transmission network. It can provide STM-1/STM-4 optical interfaces and forms the entire equipment group with the other access layer equipment, thus optimizing the Huawei OptiX product series.
The OptiX OSN 500 is used at the access layer of the transmission network. It can provide STM-1/STM-4 optical interfaces and forms the entire equipment group with the other access layer equipment, thus optimizing the Huawei OptiX product series.
Except for the basic principles for planning a network, you need to plan a network according to the NE type and networking mode supported by the OptiX OSN 500. The OptiX OSN 500 can form a network alone or with Huawei SDH equipment or third-party transmission equipment.
The OptiX OSN 500 can form a chain or ring network alone.
The OptiX OSN 500 can form a network with other transmission equipment.
The OptiX OSN 500 supports various types of services and provides abundant functions and features, to ensure the quality and efficiency of the service transmission.
The OptiX OSN 500 can access the following types of services:
SDH service signals
PDH service signals
Ethernet service signals
The service capacity of the OptiX OSN 500 consists of the cross-connect capacity and the maximum access capacity.
Cross-Connect Capacity
The OptiX OSN 500 supports the higher-order full cross-connections of 21.25 Gbit/s or lower-order full cross-connections of 5 Gbit/s.
Access Capacities of Slots
This section provides slot access capacities of the OptiX OSN 500.
Maximum Access Capability
The OptiX OSN 500 can access services through various interfaces.
The OptiX OSN 500 can form multiple network topologies such as the ring network and chain network.
The OptiX OSN 500 supports separate and combined configuration of the following types of NEs: terminal multiplexer (TM) and add/drop multiplexer (ADM). The OptiX OSN 500 can form a chain or ring network by using the STM-1/STM-4 optical interfaces.
When the OptiX OSN 500 functions as the access equipment, it can network with Huawei Metro and OSN equipment series. The OptiX OSN 500 can also network with third-party equipment.
The OptiX OSN 500 adopts the T2000 as the integrated NMS.
The T2000 can implement the integrated management of the entire optical transmission system and can also provide end-to-end management function if required. The T2000 improves the network quality and reduces maintenance costs, thus ensuring reasonable utilization of network resources.
An login to the LCT is not allowed during an login to the NMS. After a 30-minute logout of the NMS, an login to the LCT is allowed.
The software system is of a modular design. Each module provides specific functions and works with other modules.
The entire software is distributed in three modules including board software, NE software and NM system.
The software resides respectively on functional boards, the SCC, and NM computer. Hierarchical structure ensures that it is highly reliable and efficient. Each layer performs specific functions and provides service for the upper layer.
Table 1 Weight, dimensions, and power consumption of the OptiX OSN 500
Equipment OptiX OSN 500
Power Consumption About 46 W (full configuration)
Weight About 4 kg (full configuration)
Dimensions 442 mm (width) x 220 mm (depth) x 44 mm (height) (1U)
Table 2 Service access capacity of the OptiX OSN 500
Service Type Maximum Number of Services Supported (channel)
STM-4 standard services 2
STM-1 standard services 6
E3/T3 services 6
E1/T1 services 105
Fast Ethernet (FE) services 24
Gigabit Ethernet (GE) services 2
Table 3 Power consumption and weight of the boards on the OptiX OSN 500
Board Power Consumption (W) Weight (kg)
ISU 21.3 1.12
SL1D 3.5 0.3
SP3D 11.9 0.85
PL3T 4.5 0.3
EGT1 8.3 0.6
EFS8 13 0.65
Table 4 Climate requirements for storage
Item Scope
Altitude ≤ 4,000 m
Air pressure 70 kPa to 106 kPa
Temperature -40°C to +70°C
Temperature change rate ≤ 1°C/min
Relative humidity 5%-100%
Solar radiation ≤ 1120 W/s2
Heat radiation ≤ 600 W/s2
Wind speed ≤ 30 m/s
S1018750 Typical Configuration
02310GEJ | TNHMMODELF02 | 8xFE/21xE1/75ohm/2xSTM-1(S-1.1) Main control Equipment integrated photoelectric optical transmission module(220VAC),4*(FC-LC,10m)/1*75ohm(10m)/Symmetric Twisted-Pair(30m) |
TNHB00CASE01 | Assembly Chassis(220V) | |
TNHD00ISUC01 | 8xFE/21xE1/75ohm/2xSTM-1(S-1.1,LC)Integrated System Control Unit,ESFP Opitcal Module | |
FSFL01001 | Fibre-optical jumper wire-LC/UPC-FC/UPC-single mode-G.657A2-2mm-10m | |
T-75-21-Anea 96F-10 | Trunk Cable,10m,75ohm,21E1,1.6mm,Anea 96F-I,SYFVZP75-1.1/0.26*42(S),+45deg | |
CAB-DL4217-30 | DL4217-standard network cable30m-8PIN connector/8 corecategory 5 cable/8PIN connector-HONET | |
02310GEH | TNHMMODELE02 | 8xFE/21xE1/75ohm/2xSTM-4(S-4.1) Main control Equipment integrated photoelectric optical transmission module(-48VDC),4*(FC-LC,10m)/1*75ohm(10m)/Symmetric Twisted-Pair(30m) |
TNHB1CASE | Assembly Chassis(-48V) | |
TNHD00ISUC03 | 8xFE/21xE1/75ohm/2xSTM-4(S-4.1,LC)Integrated System Control Unit,ESFP Opitcal Module | |
FSFL01001 | Fibre-optical jumper wire-LC/UPC-FC/UPC-single mode-G.657A2-2mm-10m | |
T-75-21-Anea 96F-10 | Trunk Cable,10m,75ohm,21E1,1.6mm,Anea 96F-I,SYFVZP75-1.1/0.26*42(S),+45deg | |
CAB-DL4217-30 | DL4217-standard network cable30m-8PIN connector/8 core category 5 cable/8PIN connector-HONET | |
machine box size | 442mm(W)×220mm(D)×44mm(H) | |
machine box weight | 2kg(NW of machine boxjust include POWER and FAN) | |
Copyright © 2019YANTAI YUNPAN INTERNATIONAL TRADE CO.,LTD. | All Rights Reserved
Hello, please leave your name and email here before chat online so that we won't miss your message and contact you smoothly.
