Optix Osn 9800 Tnu6n502t22 2*200g/100g Programmable Line Service Processing...

The N502 board supports the transmission of OTN.

The N502 board can work in either line mode or relay mode.

Table 1 Function differences between port modes

Function and Feature		Working Mode of the Port
Function and Feature		100G Mode	200G Mode	400G Mode
Supported port		Port 1, port 2	Port 1, port 2	Port 1. And port 2 must be set to NONE Mode.
Carrier technology		Single-carrier technology	Single-carrier technology	The board in 400G mode uses the dual-carrier technology and transmits or receives signals at port 1 and port 2.
Basic function	Line mode	Supports the following service conversions: 80 x ODU0/ 40 x ODU1/ 10 x ODU2/ 10 x ODU2e/ 2 x ODU3/ 1 x ODU4/ 80 x ODUflex <-> 1 x ODU4 <-> 1 x OTU4.	Supports the following service conversions: 160 x ODU0/ 80 x ODU1/ 20 x ODU2/ 20 x ODU2e/ 4 x ODU3/ 2 x ODU4/ 160 x ODUflex <-> 2 x ODU4 <-> 1 x ODUC2 <-> 1 x OTUC2.	Supports the following service conversions: 320 x ODU0/ 160 x ODU1/ 40 x ODU2/ 40 x ODU2e/ 8 x ODU3/ 4 x ODU4/ 320 x ODUflex <-> 4 x ODU4 <-> 1 x ODUC4 <-> 1xOTUC4
Basic function	Relay mode	Electrically regenerates OTU4 signals at an electrical REG station. Supported service rate: OTU4, at a rate of 111.81 Gbit/s	Electrically regenerates OTUC2 signals at an electrical REG station. Supported service rate: OTUC2, at a rate of 224.61 Gbit/s	Electrically regenerates one OTUC4 signal at an electrical REG station. Supported service rate: OTUC4, at a rate of 449.22 Gbit/s
FEC		SDFEC2	200G ePDM-16QAM:SDFEC 200G ePDM-16QAM-H:SDFEC 200G ePDM-e16QAM:SDFEC2	400G ePDM-16QAM(Dual_Ports): SDFEC 400G ePDM-16QAM-H(Dual_Ports): SDFEC 400G ePDM-e16QAM(Dual_Ports): SDFEC2
Line modulation format		100G ePDM-QPSK wDCM 100G ePDM-QPSK	200G ePDM-16QAM 200G ePDM-16QAM-H 200G ePDM-e16QAM	400G ePDM-16QAM(Dual_Ports) 400G ePDM-16QAM-H(Dual_Ports) 400G ePDM-e16QAM(Dual_Ports)

Line Mode

Table 2 OTN functions and features of the board (line mode)

Function and Feature	Description
WDM specification	Supports ITU-T G.694.1-compliant DWDM specifications.
Tunable wavelength function	The board supports tunable wavelengths of WDM-side optical signals in Super C band (1524 nm to 1573 nm).
PRBS test function	Supports the PRBS function on the WDM side.
Alarm and performance event monitoring	Monitors BIP8 bytes (Bursty mode) to help locate line failures. Monitors parameters such as the bias current, temperature, and optical power of the laser. Monitors OTN alarms and performance events.
Regeneration board	Supported
Latency measurement	The board supports latency measurement in the WDM-side optical port direction (upstream direction).
Test frame	Not supported
Physical clock	Supported
IEEE 1588v2	Not supported
ITU-T G.8275.1	Not supported
ITU-T G.8273.2	Not supported
Typical channel spacing	200G ePDM-e16QAM:50GHz Flex/ 62.5GHz Flex/75GHz Flex Others modulation format: 50GHz Fix.
Electrical-layer ASON	Supported
Optical-layer ASON	Supported NOTE: Only ASON without optical parameters is supported in high SOP mode.
Protection schemes	Supports ODUk SNCP. Supports tributary SNCP protection. Supports intra-board 1+1 protection (when working with the QCP or OLP or DCP board). NOTE: When the cross-connect granularity is ODUflex, the board does not support tributary SNCP protection. Port in 400G mode: Do not support intra-board 1+1 protection.
Loopback	WDM-Side Loopback	Supported
Loopback	Channel Loopback	Port in 100G mode: ODUk (k = 0, 1, 2, 2e, 3, or flex) channel loopbacks Port in 200G mode or 400G mode: ODUk (k=0, 1, 2, 2e, 3, 4, flex) channel loopbacks.
ESC	Supported

Relay mode

Table 3 Functions and features of the board (relay mode)

Function and Feature	Description
Basic function	The N502 board applies to electrical regeneration sites to provide the electrical regeneration function for optical signals using port 1 and port 2.
Supported service rate	OTU4: OTN service at a rate of 111.81 Gbit/s OTUC2: OTN service at a rate of 224.61 Gbit/s OTUC4: OTN service at a rate of 449.22 Gbit/s
WDM specification	Supports ITU-T G.694.1-compliant DWDM specifications.
Tunable wavelength function	The board supports tunable wavelengths of WDM-side optical signals in Super C band (1524 nm to 1573 nm).
ESC function	Supported
PRBS function	Not supported
Alarm and performance event monitoring	Monitors BIP8 bytes (Bursty mode) to help locate line failures. Monitors parameters such as the bias current, temperature, and optical power of the laser. Monitors OTN alarms and performance events.
Test frame	Not supported
Physical clock	Not supported
IEEE 1588v2	Not supported
Optical-layer ASON	Supported NOTE: Only ASON without optical parameters is supported in high SOP mode.
Protection scheme	Not supported
Loopback	Not supported

PRODUCT

OptiX OSN 9800 TNU6N502T22 2*200G/100G programmable line service processing board(CFP) -- OSN9800

Line Mode

Relay mode